Features
| Features | Benefits |
| Surpassed rugged industry standards | All Land Pride Cutters have been designed and tested and meet rigorous voluntary testing procedures. |
| Factory assembled | Saves customer set-up time and money. |
| 160 HP Divider gearbox and 75 HP wing gearboxes | A rugged heavy built gearboxes capable of handling heavy cutting applications. |
| Gearbox Seal Protection | Gearbox bottom seal protection for longer bearing life. |
| Input driveline: Cat. 4 CV | Driveline is matched just right for capacity of tractor. Constant velocity (CV) U-joint allows for 80 degree turns without doing damage to the driveline. |
| Easy greasable drivelines | Drivelines have access holes for greasing the U-joints and to grease the inner profiles. |
| 2 Plate slip-clutch | Protects drivelines and gearboxes by slipping clutches rather than twisting the driveline when impacts are encountered. |
| 15,000 FPM High blade tip speed | Allows clean cutting of material and even distribution. |
| 6" Blade overlap | Eliminates skipping during turns. |
| 11 1/4" Deck height | Handles heavy cutting, which reduces balling-up of cut material under the deck. |
| 3/16" Gauge Stump jumper backed with a 1" thick mounting bar | Allows cutter to slide over obstructions protecting gearbox output shaft & bottom seal. |
| 10 Gauge smooth deck top | Reduces accumulation of debris and is easier and faster to clean. |
| 1/4" Plate side skirt | Reduces debris piercing possibilities. |
| Low hitch weight | Less drawbar wear. Less ballast required. Works well with lighter tractors. |
| Dual remote hydraulics | Easy to operate. Fits most tractors, only two duplex outlets required to lift wings and change cutting height separately. |
| Hinged wing sections | Allows cutter to follow terrain. Ideal for rough ground where hillsides, ditches and hollows can cause uneven cutting. Wings will hinge 20o down. |
| 7/8" Solid hinge rods | Gives great strength to the cutter from front to rear, and in the hinge area itself. |
| Wing transport locks | Holds transport wings in the folded-up position in case of hydraulic pressure loss. |
| Enclosed front to rear dual leveling rods | Dual leveling rods enable the cutter to pull equally on the rear axle during travel over rough terrain. Many competitors only use one leveling rod. |
| 5-Bolt hubs | 5-Bolt hubs makes the wheel assembly more durable and longer lasting. |
| Drain holes in wheel rims | Allows water to drain from wheels mounted on folded-up wings. Helps prevent paint deterioration and rusting to the wheel rims. |
| Spring-cushioned lift cylinder | Cushions loads on drawbar. |
| Replaceable wheel spindles | Wheel spindles can be replaced when damaged without replacing the entire axle. Simply remove two bolts to replace damaged spindle. |
| 7/8" Leveling rods | Large diameter leveling rods provide superior supporting strength over rough terrain. |
| Airplane tires | Gives better cushion while transporting and provides flotation in soft ground. |
| Specifications & Capacities | RC2515 |
| Tractor horsepower | 50-100 hp |
| Gearbox horsepower Splitter Center & wings | 160 hp 100 hp |
| Gearbox shafts input shaft output shaft | 1 3/8" 6 Spline 1 5/8" |
| Gearbox capacity & lubrication splitter center & wings | 4.5 Pints of gear lube 80-90W EP 5.75 Lints of gear lube 80-90W EP |
| Cutting capacity | 1 1/2" |
| Hitch weight | 1,022 lbs. |
| Machine weight | 3,202 lbs. with chain guards & four laminated tires. |
| Blade tip speed at 540 rpm | Center blades & wing blades = 14,963 FPM |
| Hitch types | Pull-type hitch & clevis |
| Hitch jack | Standard (2,000 lbs.) |
| Cutting width Overall width Normal transport width Minimum transport width | 15' - 0" 15' - 7" 10' - 2 1/2" With transport locks set and cutting blade 13" off the ground. 8' - 4" With transport locks set and cutting blade 2" off the ground. |
| Overall length | 15' - 2" With laminated tires 15' - 5 1/2" With aircraft tires |
| Deck height | 11 1/4" |
| Cutting height | 2" to 13" |
| Lift hydraulics | 2 1/2" x 8" hydraulic cylinder, hoses, fittings & stroke control spacers |
| Wing hydraulics | 2 1/2" x 10" hydraulic cylinders, hoses & fittings |
| Wing transport protection | Wing transport locks |
| Deck material | 10 Gauge deck |
| Side skirt material | 1/4" Plate |
| Skid shoes | Wing Deck: 1 replaceable shoe per wing Center Deck: 2 replaceable shoes |
| Blade rotation left wing center deck right wing | Clockwise Counterclockwise Counterclockwise |
| Blades - 6 (2 per deck) | 1/2" x 4" Heat treated free swinging alloy steel with up lift |
| Blade overlap | 6" |
| Blade bolt | Keyed with hardened flat washer & locknut |
| Stump jumper / blade holder | 10 Gauge round dish shaped pan, reinforced with 1" x 4" blade bar |
| Front & rear guards | Single chain or rubber |
| Input driveline | ASAE Category 4 with constant velocity u-joint |
| Intermediate & wing drivelines | ASAE Category 3 with slip-clutch |
| Wheels | 29" Used aircraft tires or 21" laminated wheels |
| Number of wheels | 4 or 6 Total |
| Transport axle | Spring-cushioned lift cylinder |
| Hubs | Cast iron five-bolt hubs with tapered roller bearings and 1 3/4" shafts |
| Colors | Standard color: Beige; Optional colors: Green, Orange, or Red |
© Copyright 2026 Kunau Implement All Rights Reserved - Site by EquipmentLocator.com
